4" LED ICAT New Construction HOUSING

HALO LED H4 Ser ies

The Halo H4 LED is a family of 4� aperture recessed downlight housings designed for use with Halo EL4 Series LED Light Engines and compatible 4� LED trims. Halo H4 LED housings have integral LED drivers that offer dimming as a standard feature.

H456ICAT120D is an insulated ceiling, AIR-TITETM housing offering 120 volt dimming capability with many incandescent or electronic low voltage dimmers. Designed for use with EL4 series LED Light Engines and TL4 LED Series Trims, the H456ICAT120D offers high quality downlighting along with high efficacy � the result being great lighting and significant energy savings.

DESIGN FEATURES

MECHANICAL

Housings

� Box enclosure of formed aluminum construction.

� Openings are gasketed AIR-TITE.

� Designed for insulated ceilings in direct contact with insulation. (May also be installed in non-insulated ceilings.)

Plaster Frame

� Galvanized steel die-formed construction.

� The housing can be removed from plaster frame to provide access to the junction box.

� Plaster frame features include:

- Patented regressed locking screw positioned for securing hanger bars from below the ceiling.

- Cutouts for easily crimping hanger bars in position.

- AIR-TITE aperture gasket is pre-installed.

- HALO identity embossed on plaster frame.

GOT NAIL! Pass -N-Thru�

Bar Hangers

� Pre-installed nail easily installs in regular lumber, engineered lumber and laminated beams.

� Safety and guidance system prevents snagging, ensures smooth straight nail penetration and allows bar hangers to be easily removed if necessary.

� Automatic leveling flange aligns the housing and lets you hold the housing in place with one hand while driving nails.

� Housing can be positioned at any point within 24� joist span.

� Pass-N-Thru� feature allows bar hangers to be shortened without removing from plaster frame.

� Score lines allow �tooless� shortening for 12� joists.

� Bar hangers may be repositioned 90�.

� Integral T-bar clip snaps onto T-bars - no additional clips required.

Slide-N-Side� Junction Box

� Positioned to accommodate straight conduit runs

� Seven 1/2� trade size conduit knockouts with true pry-out slots

� Slide-N-Side� wire traps allow non-metallic sheathed cable to be installed without tools and without removing knockouts.

� Accepts a wide range of non-metallic (type NM) sheathed cables - the standard cable types used in lighting in both U.S. and Canada.

- Allows wiring connections to be made outside the junction box

- Simply insert the cable directly into the trap after connections are made.

- Accommodates the following standard non-metallic sheathed cable sizes: (US) #14/2, #14/3, #12/2, #12/3 (Canada) #14/2, #14/3, #12/2

LED Connection

� LED connector is a non-screw base connector offering easy installation with the EL4 Series LED Light Engine.

� LED connector meets California Title-24 high-efficacy luminaire requirement for a non-screw base socket, and where required to qualify as a high-efficacy luminaire.

LED Driver

� LED dimmable driver mounts to the housing.

� Driver is a120 Volt, high efficiency, electronic power supply providing low voltage power to EL Series LED Light Engines.

� Driver meets FCC EMI/RFI Consumer Level limits for use in residential and commercial installations.

� Driver features high power factor and low THD and has integral thermal protection in the event of over temperature or internal failure.

� Driver is specifically designed for compatibility with EL4 LED Light Engines, and operates the LED for long life, meeting 50,000 hour / 70% lumen maintenance standard.

� If dimming is not required the fixture can be operated from a standard wall switch. Dimming

� The HALO H4 LED luminaire is dimmable to 15% with most standard 120V dimmers; including LED-rated and electronic low voltage dimmers (recommended); many

incandescent and magnetic low voltage dimmers; and dims to 5% using dimmers with low end trim adjustment.

� Standard incandescent dimmers require a minimum load of typically over 40 watts on the circuit for full range dimming performance (four LED modules).

� For dimming with digital (smart) multi-location dimmers or when dimming fewer than four LED modules, LED rated or electronic low voltage dimmers are required (ELV dimmers need a neutral connection in the wallbox).

Labels

� UL/cUL Listed 1598 Luminaire

� UL/cUL Listed for Damp Location

� UL/cUL Listed for Wet Location, covered ceiling - with select trims

� UL/cUL listed for Feed Through

� UL/cUL listed for Direct Contact with insulation and combustible material

Compliance

� Use with designated LED light engines and trims for ENERGY STAR� qualification.

� Can be used for State of California Title 24 high efficacy compliance with designated LED light engines and trims.

� Can be used for International Energy Conservation Code (IECC) high efficacy compliance with designated LED light engines and trims.

� Refer to specification sheets online for compliance information. Qualification

IC and AIR-TITE�

Certified under ASTM-E283 and listed UL/cUL 1598. May be used to meet insulated ceiling and restricted air-flow requirements such as:

� Washington State Energy Code

� International Energy Conservation Code (IECC)

� New York State Energy Conservation Construction Code (NY-ECCC)

� State of California Title 24 �Recessed Luminaires in Insulated Ceilings.�