6" LED Recessed New Construction Housing (for Integrated LED Trims and Modules)

HALO E750ICAT 6" LED Recessed New Construction Housing (for Integrated LED Trims and Modules)
HALO LED ICAT HOUSING for NEW CONSTRUCTION
Recessed 6" aperture new construction housing for use with LED integrated trims or modules. Suitable for 2x8 residential framing or commercial plenum construction, type IC rated and can be used in direct contact with insulation*. Airtight rating reduces airflow between living spaces and unconditioned areas providing additional energy savings. Use with Halo� LT56, SMD6, RL56, RA56, SLD6 LED integrated trims and the ML56 LED modular recessed lighting system.
DESIGN FEATURES
Housings
� Single wall precision rolled aluminum housing with interlocking construction maintains concentricity
� Adjusts vertically to accommodate 3/8" to 1" thick ceilings and locks in position with (3) setscrews
� V notches facilitate use of guide strings or laser lines for precise positioning
� Shipped with paint overspray protector installed
� Housing can be removed from below the ceiling for service or splice inspection
Plaster Frame
� Compact galvanized steel plaster frame with integral bar hanger receivers
� (2) regressed screws provide positive horizontal bar hanger locking from below the ceiling
� Integral gasket achieves ASTM-E283 airtight code compliance without additional gaskets or caulk
Junction Box
� Compact galvanized steel junction box with 16in� internal volume
� Listed for (10) #12 or (14) #14 AWG 90˚ C splice conductors
� (4) 1/2" conduit pryouts positioned to allow straight conduit runs
� (3) Slide-N-Side� nonmetallic (NM) wire traps allows wiring outside the box
� Accepts 14-2, 14-3, 12-2, 12-3 U.S. and 14-2, 14-3, 12-2 Canadian NM cable
� (3) 4-port push wire nuts with clear caps for quick and reliable mains voltage connections
� Hinged door with offset cover for easy wire access
� Junction box is repositionable 90� on plaster frame to avoid obstructions
Bar Hangers
� Captive preinstalled All-Nail� bar hangers support housing at any point along span
� Pass-N-Thru� feature adjust bars from 7-1/4� to 24� wide without removal
� Score lines allow "tool-less" shortening for 12˝ joists
� Captive nail penetrates standard and engineered lumber
� Leveling flange aligns plaster frame with framing
� Integral clip attaches directly to tee-bar
Connector
� Two-conductor wire mount connector is rated for 120-277V CAUTION- verify LED module input voltage is compatible with the input voltage of the housing. If uncertain, consult a qualified electrician
� cULus listed with Halo� LT56, SMD6, RL56, RA56, SLD6 and ML56 family of LED integrated trims
Code Compliance
� Type IC inherently protected, suitable for direct contact to air permeable insulation and cULus listed for damp locations
� Not for use in direct contact with spray foam insulation, consult NEMA LSD57-2013
� Wet location listed in covered ceilings and IP56 certified with select trims
� Airtight per ASTM-E283
� Can be used for State of California Title 24 high efficacy luminaire compliance
� Suitable for use in clothes closets when installed in accordance with the NEC 410.16 spacing requirements
� Contains no mercury or lead and RoHS compliant
Warranty
� Five year limited warranty, consult website for details www.eaton.com/lighting/Legal
* Not to be used in direct contact with spray foam insulation.
A complete luminaire consists of a housing, LED integrated trim or LED module and trim, order separately.
Trims
LT56 Family
SMD6 Family
RA56 Family
RL56 Family
SLD6 Family
ML56 Family